上保护层开采底板破坏深度和应力分析研究

上保护层开采导致的底板变形、应力释放会使被保护层内高瓦斯沿着上覆岩层内形成的空隙裂隙结构向上运移，很容易造成所采工作面采空区内瓦斯增加，造成工作面瓦斯超限。以峰峰集团以黄沙矿为研究实例，针对其主采的2号煤层利用FLAC^3D模拟软件进行上保护层开采底板应力研究，揭示了上保护层开采底板应力的规律特性，对于保护层开采工作瓦斯治理具有一定的指导意义。     

高瓦斯突出矿井底抽巷一巷多用技术研究与实践

胡底煤业为高瓦斯高突出高矿压的三高矿井。对高瓦斯高突出的治理，该矿采用“地面网络预抽、区域模块降量、底抽穿层保掘、高位顺层保采”的四级模式，施工底抽巷，实现“底抽穿层消突、区域模块降量、异巷探测增效、多巷通风治患、循环排矸减压”等“一巷多用”。该4种方法已在1303（上）、1305（上）工作面应用并推广，取得了良好的效果，大大提高了掘进效率且满足抽放、探放水、通风需要；回填矸石初步设计现已经完善，待下一步掘进将实现填矸作用。     

Sustainability of ride-hailing services in China’s mobility market: A simulation model of socio-technical system transition

As a symbol of sharing economy, ride-hailing services have spread to Asia, where various forms of services have been established according to the existing socio-technical regimes, including legal, policy, and environmental concerns. China, in particular, has accepted ride-hailing services by revising existing institutions. This study analyzes China’s acceptance of ride-hailing services in the socio-technical system context set up for legacy services. Simulation modeling, combined with transition theory and an agent-based model, is used to analyze the data. This study calculates consumer disutility based on mobility market share, reflecting consumer preference, and predicts the sustainability of ride-hailing services. The simulation results conclude that legalization and socio-technical context are of importance for sustainable mobility.     

空压机润滑油系统可靠性试验研究

对空压机润滑系统进行分析,提出了一种润滑油压力调节机构,保证了空压机在高油温时油压正常,为空压机运动件提供充分润滑,从而提高空压机运行的可靠性。实验证明了该机构是可靠的,为空压机润滑系统设计提供了参考依据。     

Crack initiation and propagation in braided SiC/SiC composite tubes: Effect of braiding angle

Crack initiation and propagation in three braided SiC/SiC composite tubes with different braiding angles are investigated by in situ tensile tests with synchrotron micro-computed tomography. Crack networks are precisely detected after an image subtraction procedure based on Digital Volume Correlation. FFT based simulations are performed on the full-resolution 3D images to assess elastic stress/strain fields. Quantitative measurements of the crack geometries are performed using a novel method based on grey levels. The results show that braiding angle has no obvious effect on the location of crack onsets (initiation always occurs at tow interfaces), whereas it significantly affects the paths of crack propagation. This work provides an explicit demonstration of the crack propagation scenarios with respect to the mesoscopic fibre architectures.     

基于分形插值的改进趋势面拟合法在地面沉降中的应用

针对区域地面沉降监测点数量有限、分布不均的情况,一般采用空间插值的手段建立表面拟合模型来解决。基于分形插值,采用随机选择迭代函数的思想对传统的趋势面拟合法作出改进,改进后拟合优度系数提高0.03,达到0.995,且改进前后的拟合结果符合显著性检验的要求。实验结果表明:改进前后趋势面拟合法拟合结果满足地面沉降监测的精度要求,改进后方法的拟合优度更高,对现实地面沉降量变化的描绘更加真实,可为沉降灾害评价工作提供更准确的依据。     

CAN-BUS系统应用一例

CAN-BUS系统自问世以来,已将近30年,当代各品牌车辆纷纷采用,但大部分技术人员对CAN总线系统既熟悉又陌生。经常能听到,但具体操作又显得有些力不从心。本文通过对奇瑞A3品牌轿车CAN总线的巧妙应用,引导大家进一步理解和应用CAN总线。     

基于WiMAX通信网络的电源监控系统的构建

分析了全球微波接入互存(WiMAX)的技术特点和算法复杂度,探讨了其在电源监控系统中的应用,提出了基于Inter WiMAX Connection 2250技术的远程电源监控系统。在讨论WiMAX物理层算法的基础上,确定了以正交频分多址(OFDMA)模式为主体的物理层通信协议,提高了信道的利用率,抑制了码间干扰,为构建电源监控系统打下了良好的基础。     

Fully coupled LES-DEM of particle interaction and agglomeration in a turbulent channel flow

Coupled large eddy simulation and the discrete element method are applied to study turbulent particle–laden flows, including particle dispersion and agglomeration, in a channel. The particle–particle interaction model is based on the Hertz–Mindlin approach with Johnson–Kendall–Roberts cohesion to allow the simulation of van der Waals forces in a dry air flow. The influence of different particle surface energies, and the impact of fluid turbulence, on agglomeration behaviour are investigated. The agglomeration rate is found to be strongly influenced by the particle surface energy, with a positive relationship observed between the two. Particle agglomeration is found to be enhanced in two separate regions within the channel. First, in the near-wall region due to the high particle concentration there driven by turbophoresis, and secondly in the buffer region where the high turbulence intensity enhances particle–particle interactions.     

多晶硅锭中硬质点分析及控制研究

以多晶硅锭中硬质点为研究对象,通过实验研究和数值模拟的方法,对多晶硅锭中硬质点进行形貌和成分分析,并提出改善控制方法。研究结果表明硅锭中部的硬质点较细小,主要由SiC组成;硅锭头部的硬质点较粗大,主要由SiC和Si3N4组成,还有少量O的存在。进一步研究发现多晶硅定向凝固铸锭炉的热场结构对于多晶硅锭硬质点形成有直接影响,通过改进热场结构,优化晶体生长界面,显著减少了铸锭中硬质点的数量。